差别
这里会显示出您选择的修订版和当前版本之间的差别。
| 两侧同时换到之前的修订记录 前一修订版 后一修订版 | 前一修订版 | ||
|
ldo [2016/06/02 19:19] gongyu [器件] |
ldo [2016/06/02 19:51] (当前版本) gongyu [输出噪声] |
||
|---|---|---|---|
| 行 11: | 行 11: | ||
| ====稳压==== | ====稳压==== | ||
| - | Low-dropout (LDO) regulators work in the same way as all linear voltage regulators. The main difference between LDO and non-LDO regulators is their schematic topology. Instead of an emitter follower topology, low-dropout regulators use open collector or open drain topology. In this topology, the transistor may be easily driven into saturation with the voltages available to the regulator. This allows the voltage drop from the unregulated voltage to the regulated voltage to be as low as the saturation voltage across the transistor.[2]:Appendix A | + | LDO和其它的线性稳压器工作模式是一样的，LDO和非LDO的稳压器的主要区别在于它们的原理拓扑结构，LDO采用了集电极开路或漏极开路的方式，而不是一个发射极跟随的方式。采用这种结构稳压器上的电压很容易驱动晶体管进入饱和状态，这就使得从待稳定的电压到稳定的输出电压之间的压差可以低到晶体管上的饱和电压。 |
| - | For the circuit given in the figure to the right, the output voltage is given as: | + | 如上图，输出电压为: |
| V_{OUT}= \left( 1 + \frac{R_1}{R_2} \right) V_{REF} | V_{OUT}= \left( 1 + \frac{R_1}{R_2} \right) V_{REF} | ||
| - | If a bipolar transistor is used, as opposed to a field-effect transistor or JFET, significant additional power may be lost to control it, whereas non-LDO regulators take that power from voltage drop itself. For high voltages under very low In-Out difference there will be significant power loss in the control circuit.[5] | + | 如果采用的是三极管，而不是场效应管或JFET，为控制它需要比较大的附加能量，非LDO会自身消耗掉压降导致的能量，For high voltages under very low In-Out difference there will be significant power loss in the control circuit. |
| - | Because the power control element functions as an inverter, another inverting amplifier is required to control it, which increases schematic complexity compared to simple linear regulator.[citation needed] | + | 因为功率控制的部分起到逆变器的作用，需要另外一个逆变的放大器来控制它，这样相对于普通的线性稳压器就增加了电路的复杂度。 |
| - | Power FETs may be preferable to reduce power consumption, but this poses problems when the regulator is used for low input voltage, as FETs usually require 5 to 10 V to close completely. Power FETs may also increase the cost. | + | 一般选用功率FET来降低功耗，但这在输入电压比较低的时候也会带来问题，因为FET一般需要5－10V才能彻底关断，功率FET也会导致成本增加。 |
| ====效率和散热==== | ====效率和散热==== | ||
| 行 63: | 行 63: | ||
| ====指标==== | ====指标==== | ||
| - | An LDO is characterized by its drop-out voltage, quiescent current, load regulation, line regulation, maximum current (which is decided by the size of the pass transistor), speed (how fast it can respond as the load varies), voltage variations in the output because of sudden transients in the load current, output capacitor and its equivalent series resistance.[10] Speed is indicated by the rise time of the current at the output as it varies from 0 mA load current (no load) to the maximum load current. This is basically decided by the bandwidth of the error amplifier. It is also expected from an LDO to provide a quiet and stable output in all circumstances (example of possible perturbation could be: sudden change of the input voltage or output current). Stability analysis put in place some performance metrics to get such a behaviour and involve placing poles and zeros appropriately. Most of the time, there is a dominant pole that arise at low frequencies while other poles and zeros are pushed at high frequencies. | + | 评价一个LDO主要的指标有： |
| + | * 电压差 | ||
| + | * 静态电流 | ||
| + | * 负载调整率 | ||
| + | * 线调整率 | ||
| + | * 最大电流（取决于导通晶体管的大小） | ||
| + | * 对负载变化的响应速度 | ||
| + | * 由于负载电流的突变、输出电容以及等效的串行阻抗对输出电压的影响 | ||
| ====电源抑制比==== | ====电源抑制比==== | ||
| 行 75: | 行 82: | ||
| ====输出噪声==== | ====输出噪声==== | ||
| - | The noise from the LDO itself must also be considered in filter design. Like other electronic devices, LDOs are affected by thermal noise, bipolar shot noise, and flicker noise.[9] Each of these phenomena contribute noise to the output voltage, mostly concentrated over the lower end of the frequency spectrum. In order to properly filter AC frequencies, an LDO must both reject ripple at the input while introducing minimal noise at the output. Efforts to attenuate ripple from the input voltage could be in vain if a noisy LDO just adds that noise back again at the output. Texas Instruments' TPS7A47 is an example of an LDO with both very low noise and high PSRR over a broad frequency band.[13] | + | LDO自身产生的噪声也应该被考虑在滤波器的设计中，与其它电子器件一样，LDO也受到热噪声、双极散射噪声、以及闪变噪声的影响。所有这些噪声叠加在一起影响了输出的电压，这些噪声主要分布在低频段。为了滤除交流频率，在输入端和输出断都要进行纹波抑制。 |
| ====负载稳压==== | ====负载稳压==== | ||
| Load regulation is a measure of the circuit’s ability to maintain the specified output voltage under varying load conditions. Load regulation is defined as: | Load regulation is a measure of the circuit’s ability to maintain the specified output voltage under varying load conditions. Load regulation is defined as: | ||